RV1310B LG Dryer Parts List

Parts assembly, svc (2 pack) (dryer drum roller assembly. Includes the roller shaft and mounting clips. As the bearing in the roller wears, it self-lubricates so no grease is neede)

The drum support roller for your dryer holds the drum in place while the drum turns on the support wheels. The drum roller is round with a bearing in the middle and measures approximately 3 inches in diameter. If the dryer is noisy, won’t tumble, or takes too long to dry, you might need to replace the support roller. It is recommended that you replace both rollers at once. The bearing inside this roller is self-lubricating, so no grease will be required. Please remember to disconnect the power to your appliance before starting your repair. This is a genuine OEM part.

Dryer lint filter (dryer lint filter. This filter should be cleaned before every load to ensure proper airflow for dryer operation. If the lint filter is ripped or torn,)

The Dryer's Lint Filter is used to collect lint during the dryer cycle as it passes through the dryer vent, in order to prevent damage to the machine. This manufacturer-approved part comes in gray, measures around 12 inches wide by 11 inches high, and is easy to install. It slides into the lint filter slot in your dryer. If there is visible damage to the screen then it's time to replace the part. We recommend that you thoroughly clean the lint filter before every load, but even with good maintenance, this hard-working part is often damaged or worn over time. If your dryer isn't drying quickly, the filter may be responsible. The manufacturer has made an authorized substitution to the lint filter. Special details: When replacing lint screen ADQ56656401 you may need to also replace lint screen housing MCK49049101 and lint screen guide MEA49050001 to prevent items from catching on the lint screen, depending on your model.

Micro switch

The microwave primary door switch, also known as a micro switch, is normally open. When the door is shut, the door switch will close to send power to the microwave to operate. If the microwave won’t start, then the switch has failed, and the part will need to be replaced. The micro switch is in the latch board section and monitors the position of the door. This part measures 1.5” L x .75” W NOTE: Due to the high voltage capacitor in the microwave, it can retain a lethal electrical charge, even when unplugged. It is suggested to have a service technician install the part. This is a genuine OEM part. Please disconnect the power to the microwave before beginning the repair.

Thermal fuse (dryer thermal fuse. If the dryer overheats, the thermal fuse blows to cut off power to the dryer. If the thermal fuse has blown, the dryer won't Star)

The high limit thermostat protects the dryer by shutting off the heating element when the dryer overheats. If the thermostat has blown, dryer won’t start or there is no heat, the thermostat will need to be replaced it can not be reset. If your dryer vent is clogged it could cause the thermostat to blow as well. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting the repair.

Lint screen housing (lint filter cover *manufacture has modified the part and suggests replacing the filter guide also)

This is an authentic dryer lint filter cover sourced directly from the manufacturer. It protects the more delicate lint filter in your dryer, so that it doesn’t get damaged and lint can’t mix in with your clothes. This product is gray in color and is made of plastic. It is sold individually. The manufacture has modified the part and suggests replacing the filter guide also. Please see your specific model information to locate the filter guide.

Glass cooking tray

This tray rotates in your microwave ensuring more even temperatures.

Moisture sensor (dryer moisture sensor bar. If the dryer timer does not advance properly inspect the moisture sensor bars for damage which can cause the automatic dryi)

The moisture sensor, also known as a humidity sensor, works in conjunction with your dryer by helping determine the amount of moisture in the drum to reduce overdrying. If the timer doesn’t advance correctly, it is suggested to check the moisture sensor bar for damage. A damaged sensor can cause the automatic drying cycle to not work properly and will need to be replaced. This is a genuine OEM part. Please remember to disconnect the power to the dryer before starting this repair.

Filter guide

This is a replacement lint screen guide for your dryer. The lint screen guide attaches to the front bulkhead and supports the lint screen. If your lint screen will not stay in place, or if you are noticing marks left on your clothes, a broken lint screen guide could be to blame. The lint screen guide is approximately 13 inches wide on its straight edge. It is made of plastic and is sold individually. This is an OEM part, directly from the manufacturer.

Blower thermostat (thermostat)

The blower housing exhaust thermostat works in conjunction with your dryer by helping to regulate the temperature inside of the dryer drum. The thermostat will turn the heat off and on to help maintain the required temperature in the drum. If your dryer is not heating the thermostat may have shorted out and will need to be replaced. This is a genuine OEM part. Please remember to shut the power off to the dryer before starting the repair.

Dryer thermistor (dryer thermistor assembly with wire harness. If the thermistor is defective, it can prolong or shorten the drying time or cause a fault code.)

The thermistor, with wire harness, helps regulate and monitor the temperature inside of the dryer. The thermistor attaches onto the blower housing. If your dryer has a short drying time or a fault code is flashing, the thermistor maybe defective and will need to be replaced. Please remember to disconnect the power to the dryer before starting the repair. This is a genuine OEM part.

Heating element assembly (dryer heating element assembly. If the dryer no longer heats then the heating element may have failed, but it is not the most common cause.)

They are all strung with a coiled wire made of a nickel and a chrome alloy. This wire receives, but resists, a controlled electric current and as a result, the wire heats up. The heat produced is used to dry the clothes in your dryer

Air duct bracket

This bracket holds the metal or plastic flapper that closes off the exhaust duct when the fan is not running and opens when the fan turns on. If the exhaust fan on your microwave does not appear to be working, the problem may be with the damper assembly. If the damper does not open and close easily, check for any damage to the bracket, and replace if it is damaged or faulty. This genuine OEM exhaust damper measures approximately 12 inches long by 5 inches wide.

Damper

The vent damper is used to close off the exhaust duct when the fan is not running, to prevent outside air from entering the microwave. When the fan turns on it allows air to vent away from the microwave. The damper measures approximately 10-inch long by 3-inchwide and is a genuine OEM part.

Thermostat assembly (thermostat)

Felt seal (felt seal, dryer drum)