JRTD226LB Jenn-Air Refrigerator Parts List

Kickplate clip (refrigerator toe grille clip)

This kickplate clip is an inch long and is made of metal. Two are needed per refrigerator.

Evaporator fan motor - 115v 60hz - blade not included (refrigerator evaporator fan motor)

The evaporator fan motor circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated. This part is 115 volts, has a 3/16th-inch shaft and is just over three inches long. It is made of both metal and plastic, and is made up of black, white, and metallic pieces. This evaporator fan motor is a genuine OEM part. Please remember to disconnect the power to your appliance before starting the repair.

Compression nut (nut)

This single 1/4-inch compression nut is used to connect the lines that supply water to the correct components, the water dispenser and the ice maker, with the plastic water line of the icemaker assembly. This is a genuine OEM part. Please remember to disconnect the power and water supply to the refrigerator before starting your repair.

Ice bin drive ring (ring)

This drive ring is three inches in diameter. It is all white in color and is made of plastic. This ring is used with a refrigeraor's icemaker assembly.

6-hour defrost timer (timer)

This part may appear different than the original, but will function the same. This device acts like a clock. It continually advances and alternates between activating the cooling cycle and the defrost heater.

Inlet hose washer (inlet gasket)

The high-pressure inlet hose washer is black in color. It is one inch in diameter, made of rubber, and used with many washing machines, refrigerators, and dishwashers. The washer helps by creating a watertight seal to avoid leaking. Over time the washer may be worn down or damaged and will need to be replaced. This is a genuine OEM part and is sold individually.

Cold control thermostat (refrigerator temperature control thermostat)

This cold control thermostat has a temperature range from 37 degrees Fahrenheit to 27 degrees Fahrenheit and a capillary length of 29 iches. This cold control thermostat cycles on and off regularly to keep your refrigerator cold.

Ice stripper (refrigerator ice maker cube ejector)

This part strips ice from the icemaker mold during the ejection cycle to prevent ice pieces from falling back into the mold. Once removed from the mold, the ice pieces are then deposited into the ice bucket ready to be dispensed. If your ice maker is not making any ice you may need to replace this part. The part is white in color and is approximately 9-inch long. The ice stripper is a genuine OEM part. Please remember to disconnect power to your refrigerator before starting your repair.

Egg tray (refrigerator egg bin)

This egg tray holds fourteen eggs.

Ice bucket auger drive motor kit (motor assy., auger (w/yo - series 10)

This motor kit comes with a thermally protected motor, a washer and a mounting bracket. The motor performs eighteen revolutions per minute, carries 115 volts, and drives the auger for the icemaker.

Plastic tubing (refrigerator water tubing)

The water supply tubing is made of plastic and goes between the water inlet valve and the ice maker inlet tube. The tubing is 8 1/2 feet long and 1/4” in diameter. The water supply tubing transports water to the ice and water dispensers. If there is no water going to the ice maker, the refrigerator is leaking, or if the ice and water dispensers are not dispensing properly, you may need to replace the water supply tubing. This is an OEM part directly from the manufacturer. Please remember to shut off the water supply and to disconnect the power to your refrigerator before starting your repair.

Screw - 6-32 x 5/16 (range screw)

This screw is well under an inch long, and is made of metal.

Ice maker front cover (refrigerator ice maker module cover)

Screw (refrigerator screw)

Sold individually.

Leveler

This is an OEM part that is made of metal and sold individually. The leveling leg is generally used with refrigerators, dryers, freezers, ranges, cooktops, and microwaves. The leveling leg is meant to keep your appliance steady and level to the floor. If you notice your appliance is uneven to the floor it may need to have the leveling leg replaced. You will notice that the bottom of the leveling leg has a smooth surface to ensure moving your appliance does not require as much effort. This part screws into a pre-drilled hole underneath the appliance.